Part Number : AQ-FX-TEMPCT
|
 | - Temperature controller is used to control leds’ working temperature so that they have long lifetime and reliable performance.
- If you select the temperature controller, we would pre-stall them on the fixture. You don’t need to install by yourself. Here are some default settings on the controller :
- Maximum Working Temperature is 34℃ . When the working temperature reach 34℃, the cooling fans on the fixture will start working automatically. It is recommended not to be higher than 38℃.
- Minimum Working Temperature is 31℃ . When the working temperature reach 31℃, the cooling fans on the fixture will stop working automatically. It is recommended not to be lower than 28℃
- Off Working Temperature is 60℃ . When the working temperature reach 60℃, the fixture will cut off power by itself (automatically); When the actual working temperature is lower than “Off Working temperature ”, the fixture start working automatically. It is recommended not to be lower than 50℃.
- These are default settings. You can set these temperature value yourself, by pressing the buttons on the controller. Please set the temperature as per our recommended temperature.
- Temperature controller can ONLY be installed on the fixtures, which is 23.62 inch (60CM) length or longer. Note : Please make a remark if you don’t want us to install the controller on the fixture.
|
|
|
$39.00
|
|
Part Number : AQ-FX-TMCT-3CH
|
 | - The timing controller is used to set the working time for each chanel ,when they start to work and when they stop working. You can set the working time separately for each chanel. Each controller has 3 chanels. We recommend 2pcs controllers for fixtures that have 4 channels or more.
- If you select the timing controller, we would pre-stall them on the fixture. Here are the default settings on the controller :
- The first chanel working time : from 9:00 PM to 9:00 AM, New York Time.
- The second chanel working time: from from 10:00 PM to 10:00 AM, New York Time.
- The third chanel working time: from from 11:00 PM to 11:00 AM, New York Time.
- You can set the working time yourself, by pressing the buttons on the controller. The fixture will turn on and turn off automatically as per your setted time. The controller has not other programs any more, like led color changing. The color changing pattern on the picture you see is only showing 3-chanel led working pattern, one chanel by one chanel, but they are not color changing pattern.
|
|
|
$39.00
|
|
Part Number : AQ-FX-UV1W
|
 | - Input voltage is 3.0-3.8V
- Power Consumption: 1W
- Forward Current: 350MA
- Led Color: Ultraviolet
- Use 1W super bright LEDs
- LEDs are made in America
- Beam Angle: 90 Degree
- Luminous Flux: 3LM
- Wavelength: 420-425NM (the favorable wavelength for coral reef )
|
|
|
$11.66
|
|
Part Number : AQ-FX-UV3W-DC
|
 | - Input voltage is 3.0-3.8V
- Power Consumption: 3W
- Forward Current: 700MA
- Led Color: Ultraviolet
- Use 3W super bright dual chip LEDs
- LEDs are made in America
- Beam Angle: 90 Degree
- Luminous Flux: 8LM
- Wavelength: 420-425NM (the favorable wavelength for coral reef )
|
|
|
$19.95
|
|
Part Number : AQ-FX-ML1W-B
|
 | - Input voltage is 3.7-3.8V
- Power Consumption: 1W
- Forward Current: 350MA
- Led Color: Blue
- Use 1W super bright LEDs
- LEDs are made in America
- Beam Angle: 90 Degree
- Luminous Flux: 15LM
- Wavelength: 450-470NM
|
|
|
$3.99
|
|
Part Number : AQ-FX-OPT
|
 | - When you purchase this item, it will be pre-installed inside the LED fixture. You don't need to install yourself.
- The switch can be controlled by both automatic and manual operation.
- When there is no light sensed in the darkness, the moon light turns on automatically. When there is light sensed at daylight time, the moon light turns off automatically.
- The automatic operation takes priority, optionally you can turn off the moon light by manual operation if you don't need.
- This switch is usually working with 2pcs moonlight 1W blue leds that you have to purchase separately.
- Any fixtures in 31.49 inch (80CM) length or longer have moon light pre-installed, so you don't need any more. Note : Please make a remark if you don’t want us to install the switch on the fixture.
|
|
|
$9.99
|
|
Part Number : AQ-FX-HM
|
 | - 4pcs base connectors
- 2pcs middle connectors
- 2pcs top connectors
- A few stainless wires
- Price is for the complete kit
- Additional height after hanged is about 60 ~ 70 inches
|
|
|
$39.00
|
|
Part Number : AQ-FX-BKT
|
 | - Height: 60MM
- Length: 105MM
- Width: 6-8MM
- Load Capacity: 50KG
- Material: Acrylic
- Price is for 4pcs per set
|
|
|
$11.50
|
|
Part Number : AQ-FX-SCR
|
 | - Product dimension : M3*10
- Screw nut is made by Stainless Steel
- Screw is made by Nylon 66
- Color: black
- Features: excellent insulation, rust free, corrosion free and light weight.
- Mainly be used to fix the brackets on the fixture.
- Price is for 8pcs per set
|
|
|
$1.95
|
|
Shopping Cart 
